FoundationsnervousPhysiology

Saltatory Conduction

Overview

Saltatory conduction is the rapid, energy-efficient propagation of action potentials along myelinated axons, where the spike regenerates only at the nodes of Ranvier and appears to jump between them. Myelin insulation lets local currents travel far with little loss, producing conduction speeds up to ~120 m/s — roughly 50 times faster than unmyelinated fibers — while using far less ATP.

Learning objectives

  • Explain the structure and function of myelin and nodes of Ranvier.
  • Describe how the action potential 'jumps' between nodes.
  • Compare conduction speed and energy cost of myelinated vs unmyelinated axons.
  • Relate axon diameter and myelination to conduction velocity.
  • Explain why demyelination slows or blocks signaling.

Process steps

1
Myelin insulates the internode

Schwann cells (PNS) or oligodendrocytes (CNS) wrap the axon in concentric myelin layers. Myelin's high electrical resistance and low capacitance mean little charge leaks out and the membrane charges quickly between nodes.

2
Action potential fires at a node of Ranvier

Nodes of Ranvier are short gaps in the myelin sheath packed with voltage-gated Na+ and K+ channels. When the incoming depolarization reaches threshold here, a full action potential regenerates.

3
Local current flows under the myelin

The node's depolarization drives local current longitudinally through the axoplasm beneath the insulated internode. Because myelin minimizes leakage, the current reaches the next node with little loss.

4
The next node is brought to threshold

Depolarization arriving at the adjacent node opens its dense voltage-gated Na+ channels, firing a fresh, full-amplitude action potential. The signal effectively 'jumps' from node to node.

5
The cycle repeats to the terminal

Each node regenerates the spike, so conduction is fast (up to ~120 m/s) and metabolically cheap — ion fluxes occur only at the nodes, so far less Na+/K+ pumping is needed per unit distance.

Key variables

VariableUnitTypical rangeRole
Conduction velocity (myelinated)m/s50-120Saltatory conduction speeds; among the fastest neural signaling in the body.
Conduction velocity (unmyelinated)m/s0.5-2Continuous conduction; slow because every membrane patch must regenerate the spike.
Internode lengthmm~0.2-2Myelin segment between nodes; longer internodes and larger diameter both raise speed, up to an optimum.
Node of Ranvier widthμm~1Tiny exposed gap concentrating voltage-gated channels for spike regeneration.

Feedback loops

Node-to-node regeneration positive feedback

  1. Node fires a full action potential
  2. Local current flows under the insulated internode
  3. Next node depolarizes to threshold
  4. Next node fires, continuing the chain

Myelin: biological insulation

Myelin is a multilayered glial membrane wrapped around the axon — made by Schwann cells in the peripheral nervous system (one cell per segment) and oligodendrocytes in the central nervous system (one cell serving many segments). Its high resistance blocks charge leakage and its low capacitance lets the membrane voltage change quickly.

CNS vs PNS myelin

Schwann cells myelinate a single internode each and guide regeneration after injury; oligodendrocytes myelinate up to 50 segments each, but CNS axons regenerate poorly.

Nodes of Ranvier: the relay stations

The ~1 μm gaps between myelin segments are dense with voltage-gated Na+ and K+ channels — up to thousands per square micrometer. The action potential regenerates only here, which is why the signal appears to leap from node to node (saltare = to jump).

Speed and efficiency

Because current flows passively and rapidly under the insulation, myelinated fibers conduct at 50–120 m/s versus 0.5–2 m/s unmyelinated. Ion exchange happens only at nodes, so the Na+/K+ pump works far less per meter — a major energy saving for long axons like those running from spinal cord to foot.

Two ways to go faster

Nervous systems speed conduction by increasing diameter (lower internal resistance, as in squid giant axons) or by myelination (vertebrate solution — fast without giant axons).

When myelin is lost

Demyelinating conditions slow conduction because current leaks from exposed internodes and may fail to bring the next node to threshold — producing conduction block. This is the physiological basis of slowed nerve conduction studies used in diagnosis.

Key points

  • Myelin insulates internodes; action potentials regenerate only at nodes of Ranvier.
  • Local current flows passively under myelin to depolarize the next node.
  • Myelinated conduction reaches ~120 m/s, ~50× faster than unmyelinated fibers.
  • Ion fluxes occur only at nodes, making saltatory conduction energy-efficient.
  • Demyelination causes slowed conduction or conduction block.

Common misconceptions

✗ Myth: The action potential literally jumps through the air between nodes.

✓ Truth: Nothing jumps across a gap: local electrical current flows continuously through the axoplasm under the myelin. 'Jumping' describes where regeneration happens, not the current path.

✗ Myth: Myelin generates the action potential.

✓ Truth: Myelin is passive insulation with almost no voltage-gated channels. The spike is generated at the nodes; myelin just preserves the current between them.

✗ Myth: Bigger axons are always slower.

✓ Truth: Larger diameter lowers internal resistance, so for a given myelination state, bigger axons conduct faster — the fastest fibers are both large and myelinated.

Practice questions

Q1. Saltatory conduction occurs at the:
  1. axon terminals
  2. nodes of Ranvier
  3. dendritic spines
  4. synaptic cleft
Answer: B.

Action potentials regenerate at the nodes of Ranvier, the channel-rich gaps between myelin segments, and the signal jumps from node to node.

Q2. Compared with unmyelinated axons, myelinated axons conduct:
  1. slower but with larger spikes
  2. faster and with less ATP cost
  3. at the same speed but more reliably
  4. faster but with larger spikes
Answer: B.

Myelin raises speed (up to ~120 m/s) and confines ion flux to the nodes, greatly reducing the pumping work per unit distance.

Q3. Myelin increases conduction velocity mainly by:
  1. adding more voltage-gated channels
  2. increasing membrane resistance and decreasing capacitance
  3. widening the synaptic cleft
  4. raising the threshold potential
Answer: B.

High resistance prevents current leak and low capacitance speeds voltage changes, letting passive current reach the next node quickly and with little loss.

Click a question to reveal the answer and explanation.

Frequently asked questions

Why is saltatory conduction faster?

The depolarizing current travels passively under low-capacitance myelin much faster than the millisecond-scale channel gating that regenerates each spike. Fewer regeneration steps per unit distance means higher overall velocity.

Why does myelination save energy?

Na+ and K+ cross the membrane only at the tiny nodes, so the total ion flux per meter is far smaller. The Na+/K+ ATPase therefore consumes much less ATP restoring gradients.

What sets the optimal internode length?

Internodes long enough that few regenerations are needed, but short enough that passive current still brings the next node to threshold — typically 100+ times the axon diameter in an optimal design.